Cycle,

V = WR, w = 2 (PI) / T, v = 2 (PI) R / T, let's see if it works. Well, refueling V is the linear velocity, W is the angular velocity, and R is the radius of the circle

RELATED INFORMATIONS

1. Use a piece of wire on the pencil and wind it for 20 turns. As shown in the figure, use a scale to measure the width of 20 turns______ Mm. The diameter of this wire is______ Mm
2. How many mm is the length of the filament and how many mm is the diameter of the filament? It's like winding in a circle
3. When re measuring the diameter of the wire, the wire is tightly and evenly wound on the pen, the number of turns is 16, and the length of the wire is 16 It's 25 mm. What's the diameter of the thin wire?
4. How to measure the diameter of wire There is a long, thin wire, which looks like hair. How to measure the diameter of the wire roughly with a scale? Write down what you do
5. As shown in the figure, Mn and PQ are parallel smooth metal guide rails with a spacing of L. they are placed in a uniform magnetic field with a magnetic induction intensity of B and a direction perpendicular to the plane of the guide rail. M and P indirectly have a resistance of R. a metal wire AB with good contact with the guide rail and an effective resistance of R2 is placed vertically on the guide rail and moves to the right at a uniform speed V under the action of horizontal external force F, regardless of the resistance of the guide rail , then () A. The direction of current through resistance R is p → R → MB. The voltage between two points is blvc. The potential at a end is higher than that at B end. The work done by external force F is equal to Joule heat generated in the circuit
6. As shown in the figure, Mn and PQ are two parallel metal guides placed in the vertical plane and long enough, with a distance of L = 50cm. The guide is in the uniform magnetic field with a vertical paper inward magnetic induction intensity of B = 5T. A metal bar AB with a resistance of 0.1 Ω can move left and right close to the guide. Two parallel metal plates a and C with a phase distance of D = 10cm and a length of L = 20cm are connected with the two parallel guides respectively It is known that when the metal bar AB is not moving, the small ball with mass m = 10g and charge q = - 10-3c shoots into the plate along the middle line of metal plate A and C at a certain speed V0, and can just shoot out the metal plate (G is taken as 10m / S2) (1) The velocity of the ball V0; (2) if the ball does not deflect between the metal plates, the velocity and direction of the metal bar AB; (3) if the ball can be ejected between the metal plates, what conditions should be met for the uniform velocity of the metal bar AB?
7. As shown in the figure, Mn and PQ are two metal rails horizontally placed in parallel with each other, and the magnetic induction line with uniform magnetic field is vertical As shown in the figure, Mn and PQ are two metal rails horizontally placed parallel to each other. The magnetic induction line of uniform magnetic field is perpendicular to the plane of the guide rail. The left end of the guide rail is connected with a resistance of resistance value. A voltmeter is connected at both ends of the resistance. The vertical guide rail is connected across a metal rod ab. the mass, resistance and dynamic friction coefficient between AB and the guide rail are μ = 0.5, and the resistance of the guide rail is ignored. Now the constant force of F = 0.7n is used to pull AB horizontally to the right, Let it start to move from rest. After time, AB starts to move at a constant speed. At this time, the voltage expression u = 0.3V, the acceleration of gravity. Find (1) the power of external force F when AB moves at a constant speed. (2) the electric quantity passing through R during the acceleration of AB rod Mainly ask the second question, I searched, there is a "impulse theorem" to do the second question, but we did not learn. Is there any other way to ask the second question?
8. As shown in the figure, in a uniform magnetic field, the resistance of two parallel metal guide rails Mn and PQ is ignored, AB and CD are two metal slide rods As shown in the figure, in a uniform magnetic field, the resistance of two parallel metal guide rails Mn and PQ is not included, AB and CD are two metal slide rods, and the resistance rabf2 and UAB
9. As shown in the figure, the distance between two sufficiently long parallel smooth metal guide rails Mn and PQ is, the angle between the guide rail plane and the horizontal plane = 30 °, the resistance of the guide rail is not included, and the magnetic resistance is not included The uniform magnetic field with the strength of B is perpendicular to the plane of the guide rail and upward. The metal plate AB with the length of D is perpendicular to Mn PQ and placed on the guide rail, and always has good contact with the guide rail. The mass of the metal bar is m, and the resistance r = R. a bulb is connected to the upper end of the guide rail of the two metal bars, and the resistance RL = R of the bulb and the acceleration of gravity is g, A constant force of F = mg is applied to the metal rod in the direction perpendicular to the rod and parallel to the plane of the guide rail to make the metal rod move from static state. When the metal rod reaches the maximum speed, the bulb can just reach its rated power (1) The maximum velocity VM that metal bar can reach (2) Rated power of bulb pl (3) Acceleration a when the metal bar reaches half of the maximum speed (4) If the maximum sliding distance of the metal bar is l, calculate the electric heat QR generated on the metal bar during the process of the metal bar sliding up 4L from static state
10. As shown in the figure, the smooth U-shaped metal frame is still on a horizontal plane in a vertical downward uniform magnetic field. Now the AB rod suddenly obtains an initial velocity V and moves to the right A. B. the current in the circuit decreases uniformly. C. the potential of point a is lower than that of point B. D. the U-shaped frame moves to the right
11. How many centimeters is the circumference of a rectangle made by flattening five squares with 10 cm sides into a rectangle?
12. Is the distance of a harmonic motion passing through a half periodic particle twice the amplitude?
13. The central angle of a sector is 160 degrees, and the area of the sector circle is 540 square meters. What is the area of this sector?
14. Multiplication and division of decimals (20 questions each) Don't be too difficult!
15. Given that a point m (3,0) is a circle x + y minus 8x minus 2Y + 10 = 0, how to find the linear equation of the longest chord at M?
16. Solving simple mathematical problems in volume one of grade five
17. P is the point on the ellipse x ^ 2 / 25 + y ^ 2 / 16 = 1, F1 and F2 are the left and right focal points, and the angle f1pf2 = 60 °, then what is the area of △ pf1f2
18. How to solve the math problems of grade four without equations? Xiao Ming's father is 27 years older than Xiao Ming. Four years later, his father's age is four times that of Xiao Ming. How old is his father now?
19. Higher integral problem 1 / Sint DT thank you
20. Fractional multiplication and division 1. How many air conditioners are sold in the first day, one-third of them in the second day, 14 in the third day? 2. A pile of goods is transported 4 / 15 of the first time, and the second time is 2 tons more than the first time. How many tons are there? What is the probability and usage of unit "1"? Find out how to use unit 1? How to find it?